Specifications

Complete technical specifications for the TankerTherm 123 circulating glycol heater.

At a glance

Specification Value

Heater type

Circulating electric glycol heater with onboard day tank

Dimensions

38″ wide × 24″ deep × 50″ high on current units (earlier units are 46″ high)

Weight

380 lbs (173 kg)

Capacity

123,000 BTU/hr max input (13 °F temperature rise per pass through the boiler @ 19 GPM)

Power supply

480 V or 600 V 3-phase, 36 kW (see Voltage variants)

Control voltage

12 V DC, supplied by an internal 3-phase-to-12 V DC converter

Glycol temperature

Boiler digital controller holds up to 190 °F (88 °C) at the boiler outlet. PLC Tank Heat thermostat target adjustable from 80 °F to 195 °F (27 °C to 91 °C).

Venting

Through rear of chassis, temperature controlled, power vented

Construction

Powder-coated chassis, designed for outdoor installation

Controls

Onboard 2-stage boiler digital controller plus industrial PLC supervisor with integrated touchscreen HMI

Remote monitoring

Remote Output Box on rear of unit — Indicator + Strobe (digital 12 V DC, 0.5 A fused) and 0–10 V analog tank temperature (0–200 °F). See Remote Output Box.

Voltage variants

This manual covers two SKUs that differ only in voltage. The boiler heating elements and the circulation pump motor are voltage-matched to the supply; all other components are common.

SKU Power supply Notes

20-TTDNH00-03

480 VAC 3-phase, 36 kW

Standard variant.

20-TTDNH00-06

600 VAC 3-phase, 36 kW

High-voltage variant. Heater and circulation pump motor are 600 V matched. Connection block is labelled 600V-3PH.

See Power Supply Connections for wiring procedure (identical for both variants — the supply voltage is the only difference).

Performance details

Flow and pressure

Parameter Rating

Pump flow rate

20 GPM

Operating pressure range

5–20 PSI

Bypass/deadhead pressure

20 PSI

Relief valve setting

30 PSI

Thermal performance

Parameter Value

Design operating temperature

190°F (88°C)

Temperature rise

13°F per pass through the boiler @ 19 GPM

Time to reach 190°F from cold start

15–20 minutes (ambient-dependent)

User-adjustable offset (boiler controller)

±10°F (±5°C)

Tank Heat target (PLC)

80–195°F, factory setting 195°F

Tank Heat hysteresis (PLC)

1–50°F, factory setting 10°F

Storage and refill

Parameter Value

Internal storage tank

10 gallons

Refill source

55-gallon supply drum (customer-supplied)

Refill pump

Gear-type, positive displacement

Refill rate

4 GPM

Drawdown per connected tanker

3–5 gallons

Refill trigger level

50% tank volume

Refill stop level

95% tank volume

Controls

  • Boiler controller — ASME boiler with digital 2-stage temperature modulation, with a user-adjustable ±10 °F target offset (see Temperature Control)

  • Tank Heat thermostat — the PLC holds the boiler off while the storage tank is above an adjustable target (80–195 °F) and lets it run again once the tank has cooled by the set hysteresis (see Temperature Control)

  • PLC supervisor — industrial PLC with integrated touchscreen HMI (software v2.2) — see PLC Controller Overview

  • Glycol level control — Automatic, with low-level refill activation; tank level visible on the PLC Status screen

  • Enclosure temperature — Cooling fan and screen heater regulated by the PLC against ambient temperature setpoints

  • Connected tankers — Up to four at once, filled in succession and heated together

Protection summary

Protection Action

LWCO (Low-Water Cut-Off)

Hardware sensor disables boiler immediately if tank coolant is critically low; latches strobe; requires Reset

ECO high-temperature limit

Hardware over-temperature switch on the boiler

30 PSI relief valve

Boiler over-pressure protection

Fill Time Limit

PLC stops refill pump, latches strobe, and locks out the system if a single refill cycle exceeds the configured time (default 300 s). This is how the unit protects the refill pump when the supply drum runs dry.

Refill Pressure cutoff

PLC stops refill pump and latches strobe if refill pressure exceeds the configured maximum (default 20.0 PSI)

Precaution Disable

PLC pauses circulation and heat at very low tank level (~3 %) to avoid dry running while refill catches up

Refill pressure sensor fault

PLC stops the refill pump, latches the strobe, and locks out the system if the refill pressure sensor signal is below 3.5 mA or above 21.0 mA for 0.5 s (broken wire, unplugged connector or failed sensor); requires Reset

Safety features

Critical safety systems

The TankerTherm includes multiple interlocks. Do not attempt to bypass or disable any of the following:

  • Automatic refill pump shutdown if the supply drum is emptied (the Fill Time Limit)

  • ECO high-temperature limit switch — hardware over-temperature protection

  • LWCO low-coolant cut-off sensor — prevents dry-running

  • 30 PSI pressure relief valve — protects boiler from overpressure

Enclosure temperature regulation

Screen heater deprecated

The screen heater is deprecated. Current units are built without it; the cooling fan is unchanged.

The PLC regulates two independent enclosure functions: a cooling fan that ventilates the cabinet in hot weather, and a screen heater that keeps the LCD HMI warm in cold weather. Each is controlled from its own temperature sensor.

Hot weather — cooling fan (watches cabinet ambient)
  • Engages at 91 °F (33 °C)

  • Disengages below 86 °F (30 °C)

Cold weather — screen heater (watches LCD temperature)
  • Engages at 32 °F (0 °C)

  • Disengages above 37 °F (3 °C)

Setpoints are field-adjustable — see PLC Controls and Setpoints.